[Dec 13, 2023] 300-410 Sample with Accurate & Updated Questions [Q73-Q93]

Q73. Refer to the exhibit.

While monitoring VTY access to a router, an engineer notices that the router does not have any filter and anyone can access the router with username and password even though an ACL is configured.
Which command resolves this issue?

Q74. Refer to the exhibit.

An engineer has successfully set up a floating static route from the BRANCH router to the HQ network using HQ_R1 as the primary default gateway When the g0/0 goes down on HQ_R1, the branch network cannot reach the HQ network 192.168.20.0/24. Which set of configurations resolves the issue?

Q75.

Refer to the exhibit. An engineer configures router A to mark all inside to outside traffic from network 192
168 1 0, except from host 192 168 1 1. with critical IP precedence. The policy did not work as expected Which configuration resolves the issue?

Q76. Refer to the exhibit.

The branch router is configured with a default route toward the internet and has no routes configured for the HQ site that is connected through interface G2/0. The HQ router is fully configured and does not require changes. Which configuration on the branch router makes the intranet website (TCP port 80) available to the branch office users?
A)

B)

C)

D)

Q77. Refer to the exhibit.

An engineer has configured policy-based routing and applied the configured to the correct interface. How is the configuration applied to the traffic that matches the access list?

Q78.


Refer to the exhibit. An engineer Is troubleshooting a routing loop on the network to reach the 172.16.3.0/16 from the OSPF domain. Which configuration on router R1 resolves the Issue?

Q79. After some changes in the routing policy, it is noticed that the router in AS 45123 is being used as a transit AS router for several service provides. Which configuration ensures that the branch router in AS 45123 advertises only the local networks to all SP neighbors?
A)

B)

C)

D)

Q80. Which protocol is used to determine the NBMA address on the other end of a tunnel when mGRE is used?

Q81.

Refer to the exhibit. The administrator configured route advertisement to a remote low resources router to use only the default route to reach any network but failed. Which action resolves this issue?

Q82. An engineer configured Reverse Path Forwarding on an interface and noticed that the routes are dropped when a route lookup fails on that interface for a prefix that is available in the routing table Which interface configuration resolves the issue?

Q83. Which protocol does MPLS use to support traffic engineering?

Q84. Drag and drop the SNMP attributes in Cisco IOS devices from the left onto the correct SNMPv2c or SNMPV3 categories on the right.

Q85. Refer to the exhibit.

After applying IPsec, the engineer observed that the DMVPN tunnel went down, and both spoke-to-spoke and hub were not establishing. Which two actions resolve the issue? (Choose two.)

Q86. Refer to the exhibit. An engineer is trying to log in to R1 via R3 loopback address. Which action resolves the issue?

Q87. Refer to the exhibits.

When DMVPN is configured, which configuration allows spoke-to-spoke communication using loopback as a tunnel source?

Q88. Refer to the exhibit.

R5 should not receive any routes originated in the EIGRP domain. Which set of configuration changes removes the EIGRP routes from the R5 routing table to fix the issue?

Q89. Refer to the exhibit.

The Customer Edge router (AS 65500) wants to use ASC100 as the preferred ISP for all external routes.

This configuration failed to send routes to AS 100 as the preferred path. Which set of configuration resolves the issue?

Q90.

Refer to the exhibit. A network administrator configured mutual redistribution on R1 and R2 routers, which caused instability in the network. Which action resolves the issue?

Q91. Drag and Drop Question
Drag and drop the OSPF adjacency states from the left onto the correct descriptions on the right.

Q92.


Refer to the exhibit The engineer configured route redistribution in the network but soon received reports that R2 cannot access 192 168 7 0/24 and 192 168 15 0/24 subnets Which configuration resolves the issue?

Q93. Refer to the exhibit.

An engineer is trying to connect to R1 via Telnet with no success. Which configuration resolves the issue?