[Q20-Q40] Valid 4A0-205 Practice Test Dumps with 100% Passing Guarantee [Oct-2023]

It is possible to open and manage EPT designs that are created with different releases than the release installed on the local workstation, however only designs created with current and older releases can be opened and edited. Designs created with an older release can be opened by a current release but changes cannot be made.

The long-haul WT decoder parameter can be set in the NE parameters when designing a network with EPT. This parameter is used to adjust the sensitivity of the decoder and can help to improve the accuracy of the measurements for long-haul WTs.
The Network Element (NE) parameters in EPT (Element Planning Tool) are used to configure various settings and options for the network elements in the network. The long-haul WT decoder parameter is one such setting that can be configured in the NE parameters section. The user can access the NE parameters by navigating to the NE Parameters menu within the EPT interface. The user can then select the appropriate network element and modify the settings as needed. This information can be found in the Nokia guide for EPT.

The CPB (Commissioning Parameter Builder) application is used to generate the commissioning files for a Nokia 1830 Photonic Service Switch (PSS-1). The CPB application allows the user to create multiple commissioning files [1][2], which can be used to configure a variety of different features on the device. The CPB also allows users to view, edit and modify the commissioning files before they are uploaded to the device. The NSP (Network Service Platform) and EPT (Element Provisioning Tool) are used to manage the devices and network elements within the network, but do not generate commissioning files.

The OSNR is defined as the ratio between the average optical signal power and the average optical noise power over a specific spectral bandwidth. This is also known as the signal-to-noise ratio (SNR), and it is a measure of how much signal is present in the optical signal compared to the noise, usually expressed in decibels (dB).

show interface 11starla 1/17/L1 detail is the correct command to check for interface details. This command will display detailed information about the specified interface, including its status, configuration, and statistics.

Node synchronization is a process of keeping the NFM-T database in sync with the nodes in the network. The synchronization process will download all the items from the node, including NE parameters, ports, alarms, internal links, etc., to the NFM-T database. This ensures that the NFM-T database is up to date and the network is running efficiently.

Node creation, systems validation and system provisioning. The CPB (Commissioning Parameter Builder) application is used to generate commissioning files for a Nokia 1830 Photonic Service Switch (PSS-1) and can be used to create new nodes, validate the system configuration, and provision the system with the appropriate settings and parameters. Power adjustment and generation of system loss report are not related to CPB.

The EPT systems are displayed on the CPB (Commissioning Parameter Builder) panel and they can be individually selected. This allows the user to configure the network elements in the network and provision them according to their specific requirements. The systems are not reported on CPB, but through the Equipment Manager. The Equipment Manager is the interface used to configure the network elements and the EPT systems. The NFM-T is not related to the CPB and does not affect the CPB process.

The validate step in the EPT design process is used to trigger the run design action, which is responsible for verifying the consistency of the network design and fixing any errors that may exist. During the validation process, the system will compare the configuration available on the involved network elements and the design provided by EPT, and any discrepancies will be flagged for further investigation or correction.

In optical fiber propagation context, the first, second, and third window refer to different wavelength intervals where the WDM (Wavelength Division Multiplexing) optical transmission occurs.
The first window is the lowest loss window and is typically in the range of 1300-1324nm. This is the most commonly used window for long-haul communications.
The second window is the 1550 nm window and is the most widely used window for long-haul and ultra-long-haul communications. This window has a lower attenuation than the first window, but it also has more dispersion, which can limit the maximum transmission distance.
The third window is the range of 1625-1675 nm, it is also called the L-band window. This window has lower attenuation than the first and second window but its usage is limited due to the high cost of equipment and lack of commercial devices.
These windows are used in WDM systems to increase the capacity of the fiber by transmitting multiple channels of data at different wavelengths on the same fiber.
A,C,D are not correct as they are not related to the meaning of first, second, and third window in the optical fiber propagation context.
Reference:
Nokia Optical Networking Fundamentals, Nokia Press (ISBN:978-1-4822-8109-4)
https://www.nokia.com/networks/solutions/optical-networking/
https://en.wikipedia.org/wiki/Wavelength-division_multiplexing

There are two main mechanisms that can be put in place to increase network survivability: protection and restoration. Protection involves pre-allocating and reserving backup resources so that they are ready in case of a failure. Restoration involves allocating backup resources upon failure and using a 1+1 protection mechanism to recover each trail. This ensures that the network is able to re-route traffic in the event of a failure, increasing the overall survivability of the network.

show interface 11starla 1/17/L1 detail is the correct command to check for interface details. This command will display detailed information about the specified interface, including its status, configuration, and statistics.

Scattering and absorption are the main reasons for fiber attenuation. Scattering occurs when light bounces off the sides of the fiber, while absorption happens when light is absorbed by the glass or other materials that make up the fiber. Chromatic dispersion (CD) and polarization mode dispersion (PMD) are also factors that can cause attenuation, but they are not the main causes. Small channel spacing can also cause attenuation, but it is a secondary factor and is only significant in certain cases.

A pre-amplifier is an optical amplifier that is used to boost the power of the received optical signal before it is detected by the receiver in an optical communication system. This is done to overcome the loss of power that occurs as the signal travels through the optical fiber and to ensure that the receiver can detect the signal. The pre-amplification stage is typically located close to the receiver in order to minimize the distance that the signal has to travel between the amplifier and the receiver, which helps to reduce the noise and distortion in the signal.

NFM-T is a network management system designed to manage optical networks in a unified manner. It is used to design, manage, and provision optical services having IP nodes as extremities. It supports a variety of technologies, including optical and IP, and fully supports LO, LI, L2, and GMPLS applications. It is mainly focused on the Nokia 1830 PSS product family, as well as other older product families.

Tracking the protection path for a specific wavelength. The Wavelength Tracker tool is used to track the protection path of a specific wavelength, allowing the user to quickly identify any issues that may arise and take corrective action.
Wavelength Tracker tool is a feature used to monitor and track the protection path for a specific wavelength in an optical network. It can also be used to monitor and verify the working state of the protection path, and to detect and troubleshoot protection switch events. The Wavelength Tracker tool can be used to monitor the protection path for a specific wavelength, and it can also be used to trace the end-to-end path of a wavelength through the network. This tool is typically used by network operators to monitor and troubleshoot wavelength-level issues in the network, such as protection switch events or wavelength-level performance issues.

The third window (1550 nm) is where the attenuation reaches its minimum peak. This is because the materials used in fiber optic cables have minimal absorption in this wavelength range. The first and second windows (850 nm and 1300 nm respectively) have higher attenuation due to the materials used in the fiber optic cables.